Skip to content

Operational Modes

An operational mode is a configuration of powerplants and fuels that is active while a vehicle operates. It sets the vehicle's energy use and tailpipe emissions per unit of distance.

A conventional internal combustion engine vehicle (ICEV) usually operates in a single mode. Advanced drivetrains use several. A plug-in hybrid electric vehicle (PHEV), for example, uses Charge Depletion (CD, electric) and Charge Sustaining (CS, hybrid or gasoline) modes. You add operational modes to vehicles in Vehicles.

An operational mode consists of:

  • A name
  • An operational mode type, chosen from a list
  • One or more powerplants, each with its energy sources (fuels) and tailpipe emissions

The editor has two bottom tabs:

Define the Mode

The General Information tab has the mode's name and type, and the powerplants table.

  1. Enter the Name, a label of your choice.
  2. Choose the Operational Mode Type from the list (CD, CS, Electric Motor, Electric Motor (E10), Regular or Regular (E10)).
  3. Add the powerplants, as described in the next sections.

Operational mode with its name, type and powerplants table
Figure 1: Operational mode with its name, type and powerplants table

Regular or Charge Sustaining (CS)

The vehicle uses energy from the tank only, and any secondary energy storage is not depleted. A hybrid vehicle may use some battery energy to assist the petrol engine, but that is small compared with the large batteries of a PHEV.

Charge Depletion (CD)

PHEVs use this mode. It assumes that electricity from a battery is the primary source of energy.

Powerplants

A powerplant is a specific power source, such as an internal combustion engine, fuel cell, electric motor or gas turbine, operating within an operational mode. GREET.net introduced the powerplant (or powertrain) concept in 2015. It separates energy consumption from emission profiles, so you can model hypothetical vehicles and hybrids in which several powerplants drive a vehicle at the same time or in sequence. Because the power source is isolated, PyGREET measures energy and emission impacts on a well-to-wheels (WTW) basis.

Each mode has one or more powerplants. Each powerplant defines how energy is consumed and what emissions are produced. It has:

  • Energy sources
  • Tailpipe emissions

Add Energy Sources

Energy sources are the main fuels or energy carriers the powerplant consumes.

  1. Select the + icon next to the Energy Sources label in the table.
  2. Search for the resource flow and select it.
  3. Set the following for the energy source:
    • Total energy consumption per unit of distance traveled
    • Efficiency of the powerplant when it uses this energy source
    • Source

Energy sources table of an operational mode
Figure 2: Energy sources table of an operational mode

Charging and refueling efficiency

This value is the ratio of fuel or energy that reaches the vehicle's storage system (the tank or the battery) from the dispensing point (the pump or the wall). It accounts for the energy losses in the final stage of the delivery chain. For electric vehicles, it includes the charger losses between the electrical outlet and the battery terminals.

Source

Each energy source must come from a pathway or a mix. PyGREET uses it to calculate the upstream results of the vehicle's energy consumption.

PyGREET offers three energy consumption types:

Type Meaning
Consumption The energy or fuel volume the vehicle needs to travel a given distance (for example, L/100 km or kWh/mile).
MPG-Gasoline Miles per gallon of gasoline equivalent: the distance the vehicle travels on an amount of alternative fuel (hydrogen or natural gas) that holds the same energy as one gallon of gasoline.
MPG-Diesel Miles per gallon of diesel equivalent. Diesel has a higher energy density than gasoline, so you use this type to compare alternative fuels against a diesel benchmark.

Equations

When you change the energy consumption type of an energy source, PyGREET re-expresses the value you entered in the new type. See Fuel Consumption Conversion for the conversion formulas and the reference fuel heating values.

Output of a previous process

If an energy source has the source type "Output of a previous process", the operational mode is non-standard. You must model any vehicle that uses it in Pathways to generate results.

Add Tailpipe Emissions

Tailpipe emissions are the exhaust emissions the vehicle releases during fuel combustion or energy use in the mode. You express them per unit of distance traveled. They contribute to the Vehicle Operation columns in the Results table.

  1. Select the + icon under the Tailpipe Emissions section.
  2. Enter each emission. As in Conversions, you can enter SOx and CO2 manually or have PyGREET calculate them from fuel properties.
  3. To add more emissions, select the + icon next to the Tailpipe Emissions label.

Tailpipe emissions table of an operational mode
Figure 3: Tailpipe emissions table of an operational mode

Equations

The automatic SOx and CO2 calculations for a powerplant use the same carbon and sulfur balances as conversions, extended to powerplants that consume several fuels. See Carbon and Sulfur Balances. For a biogenic powertrain fuel, see Biogenic CO₂ from Combustion: PyGREET estimates biogenic CO₂ from the propagated biogenic carbon unless the powertrain already declares a CO₂ biogenic emission.